MASTOREMATA D.I.Y. SHOP - ONLINE | PGP DRYPROOF MASONRY WATERPROOF 1KG ΛΕΥΚΟ (τσιμεντοειδές στεγανωτικό επίχρισμα)
printerFriendly by cloudcms®
PGP DRYPROOF MASONRY WATERPROOF 1KG WHITE (Highly effective ready to use cement fortified waterproofing paint)
PGP DRYPROOF MASONRY WATERPROOFER is a highly
effective ready to use waterproofing paint for masonry walls. Based on a
unique solvent based combination of portland cement and acrylic
copolymer resins, exhibits excellent waterproofing properties even when
negative hydrostatic pressure is present. It is suitable for interior
and exterior use. It is the only waterproofing product offering a twin
anchoring mechanism, even on wet surfaces, providing unsurpassed
reliability.
ADVANTAGES
- 5 years guarantee for negative water pressure and up to 20 years for positive*.
- Withstands negative hydrostatic pressure for up to 7 meters of water (10 psi.)
- Ideal for use indoors or outdoors above or below ground level
- Allows surface breathing
- Cured surface may be over painted, plastered, tiled etc.
- Ready for use
- Available in white and light blue; white can be tinted to any light color.
*(Subject to correct application and to substrate quality)
APPLICATIONS
DRYPROOF MASONRY WATERPROOFER is suitable for waterproofing:
- Basement walls and foundations
- Swimming pools and fountains
- Roof tops
- Water tanks and drainage
- Drive ways and garages
- Exposed walls
- Most common masonry surfaces such as cement, mortar, concrete blocks etc.
Substrate preparation
- Surfaces must be clean from dirt, dust, grease, oil, frost and paint.
- Patch holes or cracks with hydraulic cement and smooth the patch evenly.
- Check the joint where the floor and wall meet and fill any breaks with fast setting hydraulic cement.
- Efflorescence, a white, powdery, crystal-like deposit visible on the
masonry surface must be removed with PGP CLEAN & FREE (consult
manufacturer’s directions).
- PGP DRYPROOF MASONRY WATERPROOFER may be applied on slightly damp
surfaces but best results are obtained when applied on dry surfaces. Not
warranted when used over previously painted or horizontal surfaces.
WARNING: Apply only to unpainted cementitious substrates.
Application
- Stir material thoroughly before and during application. Do not thin.
- Apply PGP DRYPROOF MASONRY WATERPROOFER in two coats with brush, roller or spray.
- For best results apply the first coat by brush, working the material
into surface pores. Allow 12 hours drying time between coats.
- The second coat may be applied by brush, roller or spray.
- If leaking is still present after two coats, it indicates that pores or pin holes are still open. Paint these areas again.
- When painting the inside of concrete fish ponds and non-potable
water tanks, allow PGP DRYPROOF MASONRY WATERPROOFER to dry at least one
week, fill with water for 48 hours, then drain and refill to control
alkalinity content before putting into service.
- Apply when air and surfaces temperatures are above 10oC.
- For best waterproofing results, wait for a dry (rain-free) period before and after application.
 |  |  |  |
|
Coverage:
2,5 - 3 m2/Lt
|
Thinning:
no
|
Application:
by brush
|
Application:
by roller
|
 |
 |
 |
 |
|
Application:
by spray gun
|
Touch dry:
3 - 4 hours 20oC
|
Hard dry:
48 hours 20oC
|
Exterior use
|
 |
 |
 |
|
Interior use
|
Application temperature:
10oC - 35oC
|
Cleaning:
with white spirit or turpentine |
Code: SHJ90500132
Price: €9.20
(including 19% VAT)
